HP Storageworks 8100 - enterprise virtual array User Manual Download Page 23 | Manualshive

Page: 23 / 408

background image

The following additional equipment is required to configure the MPX200:

•

B-series or C-series FC switch

•

Optical small form-factor pluggables (SFPs)
• FC ports, 8 Gb/s short-range SFP (AJ718A)
• FC ports, 4 Gb/s short-range SFP (A744B)
• 10-GbE ports, short-range SFP+ (455883–B21)

•

Optical FC cables, copper FC cables (direct-connect only)

•

Cat5e or Cat6 GbE network cables

•

Supported Direct Attach Copper 10GbE SFP+ Ethernet cables:
• HP ProCurve 10-GbE SFP+ 1m Direct Attach Cable (J9281B)
• HP ProCurve 10-GbE SFP+ 3m Direct Attach Cable (J9283B)
• HP ProCurve 10-GbE SFP+ 7m Direct Attach Cable (J9285B)
• HP ISS 10-GbE SFP+ 0.5m Direct Attach Cable (487649-B21)
• HP ISS 10-GbE SFP+ 1m Direct Attach Cable (487652-B21)
• HP ISS 10-GbE SFP+ 3m Direct Attach Cable (487655-B21)
• HP ISS 10-GbE SFP+ 7m Direct Attach Cable (487658-B21)
• Cisco 10-GbE SFP+ 3m Direct Attach Cable SFP-H10GB-CU3M (AP784A)
• Cisco 10-GbE SFP+ 5m Direct Attach Cable SFP-H10GB-CU5M (AP785A)
• Brocade 10-GbE SFP+ 1m Direct Attach Cable XBR-TWX-0101 (AP818A)
• Brocade 10-GbE SFP+ 3m Direct Attach Cable XBR-TWX-0301 (AP819A)
• Brocade 10-GbE SFP+ 5m Direct Attach Cable XBR-TWX-0501 (AP820A)

See

Chapter 4

and the SPOCK website at

http://www.hp.com/storage/spock

for FC switch model

support.

MPX200 configuration options

You can configure an EVA storage system for simultaneous connectivity to iSCSI and FC attached
hosts. Support for iSCSI to an EVA is provided through the MPX200 and an FC switch fabric port
(fabric attach) or the MPX200 directly connected to the EVA.

NOTE:

Directly connecting an MPX200 FC port and an EVA requires the EVA controller port to be set to
Direct.

Figure 1

illustrates an MPX200 single-blade fabric-attached configuration. This is the lowest-cost

configuration and is used when high availability for iSCSI hosts is not required.

MPX200 Multifunction Router

23

«
...
21
22
23
24
25
...
»

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Storageworks 8100 - enterprise virtual array

PoE Injector Adapter POE-32001T

Brand: UNICOM Pages: 1

Brand: HAGOR Pages: 8

Brand: Tripp Lite Pages: 2

Brand: Rosewill Pages: 10

Connectware Series

Brand: Digi Pages: 2

Brand: Tripp Lite Pages: 8

Brand: ZyXEL Communications Pages: 7

Brand: Pace Pages: 15

Brand: Intermec Pages: 102

Brand: AR Pages: 22

Brand: Acard Pages: 34

Brand: Eminent Pages: 57

Brand: Cables to Go Pages: 9

GA511 - Gigabit Ethernet PC Card

Brand: NETGEAR Pages: 50

Brand: Belkin Pages: 2

SeaLINK plus 485I

Brand: SeaLevel Pages: 20

Brand: ZyXEL Communications Pages: 95

Brand: Thrane&Thrane Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands