HP Storageworks 8100 - enterprise virtual array User Manual Download Page 55

Page: 55 / 408

Supported IP network adapters

For the latest information on IP network adapter support, see the product release notes or SPOCK at

http://www.hp.com/storage/spock

. You must sign up for an HP Passport to enable access.

Table 7

lists the IP network adapters supported by the MPX200.

Table 7 Supported IP network adapters

Network interconnect

Operating system

All standard GbE NICs/ASICs supported by Apple

Apple Mac OS X

All standard 1 Gbe or 10 GbE NICs/ASICs and TOE NICs supported by
HP for Windows 2008 and 2003
QLogic iSCSI HBAs

Microsoft Windows Server 2008,
2003, Hyper-V

All standard 1 Gbe or 10 GbE NICs/ASICs supported by HP for Linux
QLogic iSCSI HBAs

Red Hat Linux, SUSE Linux

All standard GbE NICs/ASICs supported by Sun

Sun Solaris

All standard 1 Gbe or 10 GbE NICs/ASICs supported by HP for VMware
QLogic iSCSI HBAs

VMware

IP network requirements

HP recommends the following:

•

Network protocol: TCP/IP IPv6, IPv4, Ethernet 1,000 Mb/s or 10 GbE

•

IP data—LAN/VLAN support with less than 10 ms latency; maximum of two VLANs per port, one
VLAN per protocol

•

IP management—LAN/WAN support

•

Dedicated IP network for iSCSI data

Setting up the iSCSI initiator

This section explains how to set up the iSCSI initiator.

Windows Server iSCSI initiator

For Windows Server 2008, the iSCSI initiator is included with the operating system. For Windows
Server 2003, you must install the iSCSI initiator.

MPX200 Multifunction Router

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands

HP Storageworks 8100 - enterprise virtual array, User Manual

Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands