HP Storageworks 8100 - enterprise virtual array User Manual Download Page 135

Page: 135 / 408

Verify that the heartbeat LED is blinking (once per second) and that the System fault LED does
not light.

Figure 83

shows the location of the ports and LEDs on the MPX200.

GE1

GE2

IOIOI

FC1

FC2

MGMT

GE4

GE3

HP StorageWorks

MPX200

1 GbE Blade

MPX200 Multifunction Router

26531a

Maintenance

button

Input fault LED

Heartbeat LED

System power LED

1 GbE iSCSI

ports

Management port

10/100/1000

Ethernet

RS-232 port

UID beacon

LED (blue)

8 Gb/s FC ports

1 GbE iSCSI

ports

Figure 83 MPX200 ports and LEDs

NOTE:

See the “

MPX200 chassis diagnostics

” on page 249 for a description of the LED fault

indicators.

Connect to the MPX200 from your management workstation as follows (

Figure 84

Enter

guest

at the Login prompt.

Enter

password

at the Password prompt.

NOTE:

HP recommends that you change the MPX200

guest

password after logging in.

Enter

Blade n

at the

mpx200#>

prompt, where

is the number of the blade in the chassis

being configured.

Enter

admin start

at the

mpx200 <n>

prompt, where

is the number of the blade currently

selected in the chassis.

Enter the default password

config

NOTE:

HP recommends that you change the MPX200

config

password after logging in.

MPX200 Multifunction Router

135

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands

HP Storageworks 8100 - enterprise virtual array, User Manual

Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands