HP Storageworks 8100 - enterprise virtual array User Manual Download Page 144 | Manualshive

Page: 144 / 408

background image

Users

The MPX200 supports two types of users:

•

Administrative user:

To manage the MPX200, you must be in an administrative session. The default

password for the administrator is

config

.

•

Data migration user (miguser):

This user session is required to configure migration-related activities.

The default password is

migration

. For all DSM functions, you must run a miguser session.

Getting started

This section helps you get started using DMS with the MPX200 and the mpx Manager for Data
Migration Services by describing the supported configurations, some best practices recommendations,
and hardware and software setup.

Supported configurations

This section describes the supported topologies and fabrics, and lists the supported fabric and array
types.

Fabric configuration

Figure 87

shows a typical setup for data migration with a dual-fabric high-availability (HA) configuration

with both array controller ports and one port from each MPX200 blade connected to each fabric.
This configuration enables the MPX200 to perform load balancing.

Figure 87 Single and dual blade high-availability setup

.

Table 25

shows the migration rates that can be achieved for a single blade, depending on the

bandwidth capability of the storage array.

Offline Data Migration

144

«
...
142
143
144
145
146
...
»

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Storageworks 8100 - enterprise virtual array

Brand: Paradyne Pages: 5

Brand: Paradyne Pages: 14

miniSD SCHF Series

Brand: Alps Electric Pages: 2

Brand: Sennheiser Pages: 59

Brand: Pandigital Pages: 5

Brand: Jabra Pages: 3

SNG 12/1500-OW-N

Brand: VOLTCRAFT Pages: 4

Brand: FirmTek Pages: 30

Brand: Epson Pages: 19

Brand: Epson Pages: 36

Brand: Epson Pages: 19

Brand: Epson Pages: 56

C200001 - Stylus Color 660 Inkjet Printer

Brand: Epson Pages: 67

Brand: Epson Pages: 58

PictureMate - Compact Photo Printer

Brand: Epson Pages: 126

Brand: Epson Pages: 148

Brand: Epson Pages: 152

Stylus color 600

Brand: Epson Pages: 212

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands