HP Storageworks 8100 - enterprise virtual array User Manual Download Page 36

Page: 36 / 408

Install the HP StorageWorks MPX200 bezel:

Remove the four 10-32 x 3/8 in. screws that secure the rack rails to the front of the rack.

Position the bezel support plate in front of the MPX200 chassis, with the arrows pointing
up.

Replace the four 10-32 x 3/8 in. screws, two on each side of the bezel support plate.

Install the bezel by pushing it through the white pop-in tabs on the bezel support plate (

Figure

3. Bracket arrows

1. Screw, panhead, 10-32 x 3/8 in.

4. Bezel

2. Bezel mount bracket

Figure 14 Bezel view

Installing the MPX200

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands

HP Storageworks 8100 - enterprise virtual array, User Manual

Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands