HP Storageworks 8100 - enterprise virtual array User Manual Download Page 31

Page: 31 / 408

2 Installing the MPX200

This chapter describes how to rack mount the MPX200.

Rack mounting the MPX200

Figure 8

shows the MPX200 components.

5. Screw, flathead, 10–32 x 1/4 in. (6)

1. Rack rail, inner (2)

6. Screw, panhead, 10–32 x 3/8 in. (10)

2. Rack rail, outer (2).

7. Washer, centering (10); for use on racks with square holes
only

3. Chassis rail (2)

4. Screw, flathead, 6–32 x 1/4 in. (8)

Figure 8 MPX200 components

NOTE:

You will need a crosshead screwdriver to perform the rack mount procedure.

MPX200 Multifunction Router

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands

HP Storageworks 8100 - enterprise virtual array, User Manual

Search results

Summary of Contents for Storageworks 8100 - enterprise virtual array

Reviews:

Related manuals for Storageworks 8100 - enterprise virtual array

Brands by name

Popular brands