HP Storageworks 8100 - enterprise virtual array User Manual Download Page 133 | Manualshive

Page: 133 / 408

background image

Yes

8

8M

50

No

7

4M

25

No

7

4M

20

No

6

2M

15

No

6

2M

10

No

5

1M

5

No

4

512K

2.5

No

2

128K

1 or less

Configuring an FCIP route

Step 1. Verify your system requirements

Verify that you have the following for both the local site and the remote site (see

Figure 65

on page 113):

•

HP StorageWorks MPX200 Multifunction Router 1–GbE Base Chassis or HP StorageWorks MPX200
Multifunction Router 10–1 GbE Base Chassis. Note that FCIP is currently supported only on MPX200
1 GbE ports.

•

HP Storage Works MPX200 Half Chassis FCIP License

•

Continuous Access EVA

•

EVA3000/5000 or EVA4x00/6x00/8x00 storage system

•

FC fabrics consisting of B-series or C-series switches

•

Cat 5e network cable, three per site (mgmt, (2) FCIP)

•

Optical small form-factor pluggable (SFP) transceiver and FC cable, two per site

•

MPX200 serial console cable adapter, Cat 5e network cable

Additional equipment for the local site and remote site (see

Figure 71

on page 118 and

Figure

73

, page 118) is as follows:

•

HP StorageWorks MPX200 Multifunction Router 1–GbE Upgrade Blade (MPX200 blade for re-
dundancy)
• Or HP StorageWorks MPX200 Multifunction Router 10–1 GbE Upgrade Blade. Note that FCIP

is currently supported only on MPX200 1 GbE ports.

• HP Storage Works MPX200 Full Chassis FCIP License

NOTE:

For the latest information about operating system and multipath software support, see SPOCK at the
website

http://www.hp.com/storage/spock

. You must sign up for an HP Passport to enable access.

Step 2. Pre-installation checklist

Before you begin the configuration process, contact your system administrator for the following
information for both sites:

MPX200 Multifunction Router

133

«
...
131
132
133
134
135
...
»

Summary of Contents for Storageworks 8100 - enterprise virtual array

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Storageworks 8100 - enterprise virtual array

Brand: NEC Pages: 7

Brand: Keithley Pages: 73

Brand: Allied Telesis Pages: 90

Brand: G-cluster Pages: 2

Brand: Gemtek Systems Pages: 20

Brand: Intermec Pages: 2

SANblade 2300 Series

Brand: Qlogic Pages: 12

Powerline Adaptor Kit

Brand: NETGEAR Pages: 8

Brand: KILLARK Pages: 2

Brand: Air Live Pages: 50

Brand: BenQ Pages: 14

Brand: Vivax Metrotech Pages: 72

Brand: nLight Pages: 2

SATASTAR series

Brand: NitroAV Pages: 5

Rugged AC Power Adapter

Brand: LIND Pages: 2

Brand: LIND Pages: 5

Plus-X Dual IP-8

Brand: Burk Pages: 11

StorageWorks FCA2257C

Brand: Compaq Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands