manualshive.com logo in svg

Freescale Semiconductor PXR4030, Reference Manual

Share
Download
Freescale Semiconductor PXR4030 Reference Manual Download Page 185

System Integration Unit (SIU)

Freescale Semiconductor

7-3

PXR40 Microcontroller Reference Manual, Rev. 1

7.1.2

Overview

The system integration unit (SIU) is accessed by the core through the system bus crossbar switch (XBAR) 
and the peripheral bridge A (PBRIDGE_A). 

Table 7-1

 lists the features the SIU configures:

:

7.1.3

Modes of Operation

There are several operating modes for configuring and testing the chip:

Table 7-1. SIU Features

Feature

Description

MCU reset operations

Controls the external pin boot logic

System reset operations

Monitors internal and external reset sources, and drives the RSTOUT signal
 • Power-on reset support
 • Reset status register providing last reset source to software
 • Glitch detection on reset input
 • Software controlled reset assertion

Pad configuration registers

Enables the configuration and initialization of the I/O pin electrical characteristics using 
software to select the following:
 • Active function from the set of multiplexed functions
 • Pullup and pulldown characteristics of the pin
 • Slew rate for slow and medium pads
 • Open drain mode for output pins
 • Hysteresis for input pins
 • Drive strength of bus signals for fast pads

External interrupt operations

 • 16 interrupt requests
 • Rising- or falling-edge event detection
 • Programmable digital filter for glitch rejection
 • NMI and critical interrupt control

General-purpose I/O (GPIO)

Provides uniform and discrete I/O control of MCU general-purpose I/O pins, where each 
GPIO signal has an input register and an output register.

Internal peripheral multiplexing

Provides flexibility to customize signal/pin assignments for application development that 
allows:
 • Serial and parallel chaining of DSPIs
 • Flexible selection of eQADC trigger inputs
 • Assignment of interrupt requests (IRQs) between external pins and DSPI

Table 7-2. SIU Modes of Operation

Operating Mode

Description

Normal

In normal mode, the SIU provides the register interface and logic that controls the device and 
system configuration, the reset controller, and GPIO. The SIU continues operation with no 
changes in stop mode.

Debug

SIU operation in debug mode is identical to operation in normal mode.

Summary of Contents for PXR4030



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands