Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 393

Страница: 393 / 588

17. APPLICATION OF FUNCTIONS

17 - 4

Compatibility

( : J4 new, : Equivalent to J3, : Not available)

Function Name

MR-J4

series

MR-J3/MR-J3W series

(Note 8)

mode

J3 compatibility

mode

Tough drive function

SEMI-F47 function

B0 (Note 15, 16)

Vibration tough drive

B0 (Note 15)

Instantaneous power failure tough

drive

B0 (Note 15)

3-digit alarm display

MR-J3W-_B

Diagnosis function

16 alarm histories supported

(Note 7)

Drive recorder function

B0 (Note 15)

Machine diagnosis function

B0 (Note 15)

SSCNET

III

Controller SSCNET

III/H A0

Home position return function

Others

J4 mode/J3 compatibility mode

automatic identification (Note 11)

Power monitoring function

B0 (Note 15)

Note 1. The value is at the HG series servo motor driving.

2. The motor-less operation cannot be used in the fully closed loop control mode, linear servo motor control mode, or DD motor

control mode.

3. It is not available with MR-J4W3-_B servo amplifiers.

4. It is not available with the MR-J3W-_B, MR-J4W2-_B, and MR-J4W3-_B servo amplifiers.

5. It is not available with the MR-J4W2-_B and MR-J4W3-_B servo amplifiers.

6. The minute position detection method is available instead.

Alarm history will be saved up to six times.

8. The functions of the product with modified parts (GA) in the MR-J3-_B servo amplifiers are all covered by the J3 compatibility

mode of the MR-J4-_B servo amplifiers.

9. MR-J4W3-_B servo amplifiers do not support the fully closed loop control system.

10. For MR-J4 series, the robust filter and vibration tough drive are available instead.

11. The operation mode will be identified automatically at the first controller communication. You can change the operation mode

with the application "MR-J4(W)-B mode selection".

12. When MR-J4 is used as a replacement of MR-J3-_S, "Servo forced stop selection" in [Pr. PA04] will be "Disabled (_ 1 _ _)" in

the initial setting. Change the setting as necessary.

13. This is for MR-J4-_B servo amplifier. MR-J4-_B-RJ servo amplifier is compatible with two-wire type, four-wire type, and A/B/Z-

phase differential output method.

14. It is available with only MR-J4-_B-RJ servo amplifiers. It is not available with MR-J4-_B servo amplifiers.

15. This is available when the J3 extension function is enabled. Refer to section 17.1.9 for details.

16. For servo system controllers which are available with this, contact your local sales office.

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MR-J4W2-0303B6

Отзывы:

Похожие инструкции для MR-J4W2-0303B6

Бренды по названию

Популярные бренды

Mitsubishi Electric MR-J4W2-0303B6, Инструкция по эксплуатации

Результаты поиска

Содержание MR-J4W2-0303B6

Отзывы:

Похожие инструкции для MR-J4W2-0303B6

Бренды по названию

Популярные бренды