manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Инструкция по эксплуатации, Страница: 173 / 588

Поделиться
Скачать
Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 173

6. NORMAL GAIN ADJUSTMENT 

6 -  20 

 
6.3.3 Adjustment procedure by auto tuning 

Since auto tuning is enabled before shipment from the factory, simply running the servo motor automatically 
sets the optimum gains that match the machine. Merely changing the response level setting value as 
required completes the adjustment. The adjustment procedure is as follows. 

Auto tuning adjustment

Acceleration/deceleration repeated

Auto tuning conditions

are not satisfied? (Estimation of

load to motor inertia ratio is

 difficult.)

Load to motor inertia ratio

estimation value stable?

Set [Pr. PA08] to "_ _ _ 2" and set
[Pr. PB06 Load to motor inertia
ratio/load to motor mass ratio] manually.

Adjust response level setting so

that desired response is achieved

on vibration-free level.

To 2 gain adjustment

mode 2

Requested performance

satisfied?

End

Yes

No

Yes

No

No

Yes

Acceleration/deceleration repeated

 

 

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов