Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 350 | Manualshive

Страница: 350 / 588

background image

15. USING A DIRECT DRIVE MOTOR

15 - 9

(b) Magnetic pole detection by the minute position detection method

Is the moving distance

during the magnetic pole

detection acceptable?

(Note 3)

Turn the servo amplifier power off and on again.

Execute "Forward rotation CCW" or "Reverse rotation CW" with "Positioning operation" in the test

operation mode on MR Configurator2. Set the moving distance to "0" at this time.

Set [Pr. PL08 Linear servo motor/DD motor function selection 3] to "_ _ _ 4" to set the magnetic pole

detection method to "Minute position detection method".

The magnetic pole detection is carried out.

Is the response of the

minute position detection method

of [Pr. PL17] the final value?

Has an abnormal sound or

vibration occurred during the

magnetic pole detection?

Decrease the response of the minute

position detection method of [Pr. PL17] by

two as the final setting value.

Increase the response of the minute

position detection method of [Pr. PL17] by

one.

Not

acceptable

YES

Acceptable

NO

YES

NO

Magnetic pole detection

End

Set [Pr. PL01] to "_ _ _ 0" to set "Magnetic pole detection disabled". (Note)

Check that FLS (Upper stroke limit), RLS (Lower stroke limit), and EM2 (Forced stop 2) are on, and

turn the servo amplifier power off and on again.

Turn "On (up)" the test operation select switch (SW2-1) of the servo amplifier, and then cycle the

power of the servo amplifier.

Set [Pr. PL01 Linear servo motor/DD motor function selection 1] to "_ _ _ 1" to set "Magnetic pole

detection always enabled". (Note 1)

Set the load inertia moment ratio of the direct drive motor with [Pr. PL17 Magnetic pole detection -

Minute position detection method - Function selection]. (Note 2)

1)

2)

3)

4)

5)

6)

7)

8)

Note 1. For the incremental system, the [Pr. PL01] setting is not required.

2. If the load to direct drive motor inertia ratio is unknown, perform the magnetic pole detection by the

position detection method, and then perform the auto tuning to set an estimated value.

3. For the magnetic pole detection by the minute position detection method, the maximum rotation angle

at the magnetic pole detection must be five degrees or less. To shorten the travel distance, increase
the response by the minute position detection method in [Pr. PL17].

«
...
348
349
350
351
352
...
»

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J4W2-0303B6

Бренд: Radio Shack Страницы: 20

Бренд: Pico Macom Страницы: 8

Бренд: M-Audio Страницы: 2

Бренд: ALLNIC AUDIO Страницы: 6

Бренд: Technics Страницы: 10

Бренд: Takstar Страницы: 7

Reference Amplifier

Бренд: Genesis Страницы: 2

Бренд: Wyred 4 Sound Страницы: 12

Бренд: PJB Страницы: 7

Бренд: Line Magnetic Страницы: 16

Бренд: Michigan Scientigic Страницы: 7

Digital Extender HD-D105

Бренд: RTcom Страницы: 12

Бренд: Radial Engineering Страницы: 8

Бренд: Velocity Страницы: 22

Бренд: Acoustic Страницы: 8

Бренд: Kenwood Страницы: 16

Бренд: Kenwood Страницы: 27

Бренд: Kenwood Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды