Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 588

background image

6. NORMAL GAIN ADJUSTMENT

6 - 9

(b) Amplifier command method

Input a permissible travel distance. Input it in the load-side resolution unit for the fully closed loop
control mode, and in the servo motor-side resolution unit for other control modes. In the amplifier
command method, the servo motor will be operated in a range between "current value ± permissible
travel distance". Input the permissible travel distance as large as possible within a range that the
movable part does not collide against the machine. Inputting a small permissible travel distance
decreases the possibility that the moving part will collide against the machine. However, the
estimation accuracy of the load to motor inertia ratio may be lower, resulting in improper tuning.
Also, executing the one-touch tuning in the amplifier command method will generate a command for
the following optimum tuning inside the servo amplifier to start the tuning.

Servo motor

speed

Servo motor

speed (Note)

Forward

rotation

0 r/min

Reverse

rotation

Dwell time (Note)

Deceleration

time constant

(Note)

Travel distance (Note)

Acceleration

time constant

(Note)

Note. It will be automatically generated in the servo amplifier.

Fig. 6.2 Command generated by one-touch tuning in the amplifier command method

Item Description

Travel distance

An optimum travel distance will be automatically set in the range not exceeding the user-inputted permissible
travel distance with MR Configurator2.

Servo motor speed

A speed not exceeding 1/2 of the rated speed and overspeed alarm detection level ([Pr. PC08]) will be
automatically set.

Acceleration time
constant
Deceleration time
constant

An acceleration time constant/deceleration time constant will be automatically set so as not to exceed 60% of the
rated torque and the torque limit value set at the start of one-touch tuning in the amplifier command method.

Dwell time

A dwell time in which the one-touch tuning error "C004" does not occur will be automatically set.

«
...
160
161
162
163
164
...
»

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J4W2-0303B6

Бренд: Tabor Electronics Страницы: 48

Бренд: Xtant Страницы: 12

Бренд: Audio Note Страницы: 15

Бренд: Channel Master Страницы: 2

Бренд: McIntosh Страницы: 55

Бренд: Boss Audio Systems Страницы: 19

dPatch SutterPatch

Бренд: Sutter Instrument Страницы: 2

The Trend C 300

Бренд: Harman Kardon Страницы: 4

FP10 - SCHEMA 1

Бренд: PRESONUS Страницы: 30

Бренд: LD Страницы: 56

Digital Technology XTDT3200

Бренд: XTE Electronic Страницы: 12

ZeroUno DAC-HPA

Бренд: Canever Страницы: 8

Бренд: Analog Metric Страницы: 6

Бренд: Harman Kardon Страницы: 22

Бренд: ONSIA Страницы: 7

Бренд: Labgear Страницы: 2

Бренд: Electro-Harmonix Страницы: 2

Бренд: Lanzar Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды