Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 471 | Manualshive

Страница: 471 / 588

background image

18. MR-J4W2-0303B6 SERVO AMPLIFIER

18 - 10

18.2 Installation

WARNING

To prevent electric shock, ground equipment securely.

CAUTION

Stacking in excess of the specified number of product packages is not allowed.
Install the equipment on incombustible material. Installing them directly or close to
combustibles will lead to a fire.
Install the servo amplifier and the servo motor in a load-bearing place in
accordance with the Instruction Manual.
Do not get on or put heavy load on the equipment. Otherwise, it may cause injury.
Use the equipment within the specified environment. For the environment, refer to
section 18.1.3.
Provide an adequate protection to prevent screws and other conductive matter, oil
and other combustible matter from entering the servo amplifier.
Do not block the intake and exhaust areas of the servo amplifier. Otherwise, it
may cause a malfunction.
Do not drop or strike the servo amplifier. Isolate it from all impact loads.
Do not install or operate the servo amplifier which has been damaged or has any
parts missing.
When the equipment has been stored for an extended period of time, contact your
local sales office.
When handling the servo amplifier, be careful about the edged parts such as
corners of the servo amplifier.
The servo amplifier must be installed in a metal cabinet.
The equipment must be installed in the specified direction. Otherwise, it may
cause a malfunction.
Leave specified clearances between the servo amplifier and the cabinet walls or
other equipment. Otherwise, it may cause a malfunction.
When fumigants that contain halogen materials, such as fluorine, chlorine,
bromine, and iodine, are used for disinfecting and protecting wooden packaging
from insects, they cause malfunction when entering our products. Please take
necessary precautions to ensure that remaining materials from fumigant do not
enter our products, or treat packaging with methods other than fumigation, such
as heat treatment. Additionally, disinfect and protect wood from insects before
packing the products.

The items in the following table are the same as those for MR-J4W2-_B and MR-J4W3-_B servo amplifiers.
Refer to the section of the detailed explanation field for details.

Item Detailed

explanation

Keep out foreign materials

Section 2.2

Encoder cable stress

Section 2.3

SSCNET III cable laying

Section 2.4

Inspection items

Section 2.5

Parts having service life

Section 2.6

«
...
469
470
471
472
473
...
»

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J4W2-0303B6

Бренд: Peavey Страницы: 14

SERVOSTAR 600 Series

Бренд: Kollmorgen Seidel Страницы: 68

Бренд: AR Страницы: 56

Reference 750 SE

Бренд: Audio Research Страницы: 18

Бренд: PrimaLuna Страницы: 20

Бренд: Hammond Страницы: 24

Бренд: Fender Страницы: 18

Бренд: DAPAudio Страницы: 14

AXYS Octadrive DSP-DN

Бренд: Harman Страницы: 20

3W Amplified Phone Neckloop

Бренд: Spy Earpice Страницы: 3

Бренд: JBL Страницы: 14

Бренд: Tokyo Страницы: 11

Бренд: NuForce Страницы: 9

Бренд: Inter-m Страницы: 8

Бренд: Rane Страницы: 16

Бренд: Camco Страницы: 42

Chaos ExxtremeII CXX354M

Бренд: Boss Audio Systems Страницы: 12

Бренд: Polytron Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды