manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Инструкция по эксплуатации

Этот продукт, Mitsubishi Electric MR-J4W2-0303B6, обеспечивает высокую производительность в области промышленной автоматизации. Для получения подробной информации и руководства по эксплуатации, вы можете бесплатно загрузить инструкцию с нашего сайта. manualshive.com. Легко и удобно!

Поделиться
Скачать
background image

5. PARAMETERS 

5 -  31 

 

No. 

Symbol 

Name and function 

Initial 
value 

[unit] 

Setting 

 range 

Each/ 

Common 

PB30 

PG2B 

Position loop gain after gain switching 
Set the position loop gain when the gain switching is enabled. 
When you set a value less than 1.0 rad/s, the value will be the same as [Pr. PB08]. 
This parameter is enabled only when you select "Manual mode (_ _ _ 3)" of "Gain 
adjustment mode selection" in [Pr. PA08]. 

0.0 

[rad/s] 

0.0 to  

2000.0 

Each 

PB31 

VG2B 

Speed loop gain after gain switching 
Set the speed loop gain when the gain switching is enabled. 
When you set a value less than 20 rad/s, the value will be the same as [Pr. PB09]. 
This parameter is enabled only when you select "Manual mode (_ _ _ 3)" of "Gain 
adjustment mode selection" in [Pr. PA08]. 

0 

[rad/s] 

0 

to 

65535 

Each 

PB32 

VICB 

Speed integral compensation after gain switching 
Set the speed integral compensation when the gain changing is enabled. 
When you set a value less than 0.1 ms, the value will be the same as [Pr. PB10]. 
This parameter is enabled only when you select "Manual mode (_ _ _ 3)" of "Gain 
adjustment mode selection" in [Pr. PA08]. 

0.0 

[ms] 

0.0 to  

5000.0 

Each 

PB33  VRF11B  Vibration suppression control 1 - Vibration frequency after gain switching 

Set the vibration frequency of the vibration suppression control 1 for when the gain 
switching is enabled. 
When you set a value less than 0.1 Hz, the value will be the same as [Pr. PB19]. 
This parameter is enabled only when the following conditions are fulfilled. 

"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)". 
"Vibration suppression control 1 tuning mode selection" in [Pr. PB02] is "Manual 

setting (_ _ _ 2)". 

"Gain switching selection" in [Pr. PB26] is "Control command from controller is 

enabled (_ _ _ 1)". 

Switching during driving may cause a shock. Be sure to switch them after the servo 
motor or linear servo motor stops. 

0.0 

[Hz] 

0.0 to  
300.0 

Each 

PB34  VRF12B  Vibration suppression control 1 - Resonance frequency after gain switching 

Set the resonance frequency for vibration suppression control 1 when the gain 
switching is enabled. 
When you set a value less than 0.1 Hz, the value will be the same as [Pr. PB20]. 
This parameter will be enabled only when the following conditions are fulfilled. 

"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)". 
"Vibration suppression control 1 tuning mode selection" in [Pr. PB02] is "Manual 

setting (_ _ _ 2)". 

"Gain switching selection" in [Pr. PB26] is "Control command from controller is 

enabled (_ _ _ 1)". 

Switching during driving may cause a shock. Be sure to switch them after the servo 
motor or linear servo motor stops. 

0.0 

[Hz] 

0.0 to  
300.0 

Each 

PB35  VRF13B  Vibration suppression control 1 - Vibration frequency damping after gain switching 

Set a damping of the vibration frequency for vibration suppression control 1 when the 
gain switching is enabled. 
This parameter will be enabled only when the following conditions are fulfilled. 

"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)". 
"Vibration suppression control 1 tuning mode selection" in [Pr. PB02] is "Manual 

setting (_ _ _ 2)". 

"Gain switching selection" in [Pr. PB26] is "Control command from controller is 

enabled (_ _ _ 1)". 

Switching during driving may cause a shock. Be sure to switch them after the servo 
motor or linear servo motor stops. 

0.00 

0.00 to  

0.30 

Each 

PB36  VRF14B  Vibration suppression control 1 - Resonance frequency damping after gain switching 

Set a damping of the resonance frequency for vibration suppression control 1 when 
the gain switching is enabled. 
This parameter will be enabled only when the following conditions are fulfilled. 

"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)". 
"Vibration suppression control 1 tuning mode selection" in [Pr. PB02] is "Manual 

setting (_ _ _ 2)". 

"Gain switching selection" in [Pr. PB26] is "Control command from controller is 

enabled (_ _ _ 1)". 

Switching during driving may cause a shock. Be sure to switch them after the servo 
motor or linear servo motor stops. 

0.00 

0.00 to  

0.30 

Each 

 

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J4W2-0303B6

DR. Z Amplification SRZ-65 Manual preview
SRZ-65
Бренд: DR. Z Amplification Страницы: 6
Richie Kotzen VICTORY RK50H User Manual preview
VICTORY RK50H
Бренд: Richie Kotzen Страницы: 12
Peavey Bandit 112 Operating Manual preview
Bandit 112
Бренд: Peavey Страницы: 44
Simaudio MOON i.5 Owner'S Manual preview
MOON i.5
Бренд: Simaudio Страницы: 11
NAIM NAC 112 - ISSUE 2 Manual preview
NAC 112 - ISSUE 2
Бренд: NAIM Страницы: 30
Analog Devices SSM2304 Series Manual preview
SSM2304 Series
Бренд: Analog Devices Страницы: 20
DTC Audio CHAMP PC30D User Manual preview
CHAMP PC30D
Бренд: DTC Audio Страницы: 4
Rega Brio-R User Manual preview
Brio-R
Бренд: Rega Страницы: 17
Suhr Badger 30 User Manual preview
Badger 30
Бренд: Suhr Страницы: 7
Raymer Amplifier 801-40 Operating Instructions preview
Amplifier 801-40
Бренд: Raymer Страницы: 4
Simaudio MOON Evolution MC-8 Owner'S Manual preview
MOON Evolution MC-8
Бренд: Simaudio Страницы: 11
Ssl EV3Kmini User Manual preview
EV3Kmini
Бренд: Ssl Страницы: 7
OM POWER OM2000A+ Manual preview
OM2000A+
Бренд: OM POWER Страницы: 58
CableTronix CT-9X1HD Installation Manual preview
CT-9X1HD
Бренд: CableTronix Страницы: 3
Farenheit CLX260-2 Owner'S Manual preview
CLX260-2
Бренд: Farenheit Страницы: 25
YASKAWA LEGEND SGDG Application Notes preview
LEGEND SGDG
Бренд: YASKAWA Страницы: 3
Crest Audio P3500S Specifications preview
P3500S
Бренд: Crest Audio Страницы: 1
Solton QX 700 User Manual preview
QX 700
Бренд: Solton Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды