manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Инструкция по эксплуатации, Страница: 213 / 588

Поделиться
Скачать
Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 213

7. SPECIAL ADJUSTMENT FUNCTIONS 

7 -  32 

 
7.5 Model adaptive control disabled 
 

POINT 

 

Change the parameters while the servo motor stops. 
When setting auto tuning response ([Pr. PA09]), change the setting value one by 
one to adjust with checking operation status of the servo motor. 
This is used by servo amplifiers with software version B4 or later. Check the 
software version with MR Configurator2. 

 
(1) Summary 

The servo amplifier has a model adaptive control. The servo amplifier has a virtual motor model and 
drives the servo motor following the output of the motor model in the model adaptive control. At model 
adaptive control disabled, the servo amplifier drives motor with PID control without using the model 
adaptive control. 
The following parameters are available at model adaptive control disabled. 

 

Parameter Symbol 

Name 

PB08 

PG2 

Position loop gain 

PB09 

VG2 

Speed loop gain 

PB10 

VIC 

Speed integral compensation 

 
(2) Parameter setting 

Set [Pr. PB25] to "_ _ _ 2". 

 
(3) Restrictions 

The following functions are not available at model adaptive control disabled. 

 

Function Explanation 

Forced stop deceleration function  

([Pr. PA04]) 

Disabling the model adaptive control while the forced stop 
deceleration function is enabled, [AL. 37] will occur. 
The forced stop deceleration function is enabled at factory 
setting. Set [Pr. PA04] to "0 _ _ _" (forced stop 
deceleration function disabled). 

Vibration suppression control 1  

([Pr. PB02]/[Pr. PB19]/[Pr. PB20]) 

Vibration suppression control 2  

([Pr. PB02]/[Pr. PB52]/[Pr. PB53]) 

The vibration suppression control uses the model adaptive 
control. Disabling the model adaptive control will also 
disable the vibration suppression control. 

Overshoot amount compensation  

([Pr. PB12]) 

The overshoot amount compensation uses data used by 
the model adaptive control. Disabling the model adaptive 
control will also disable the overshoot amount 
compensation. 

 
 

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов