Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 588

background image

2. INSTALLATION

2 - 1

2. INSTALLATION

WARNING

To prevent electric shock, ground each equipment securely.

CAUTION

Stacking in excess of the specified number of product packages is not allowed.
Do not hold the cables, or connectors when carrying the servo amplifier.
Otherwise, it may drop.
Install the equipment on incombustible material. Installing it directly or close to
combustibles will lead to a fire.
Install the servo amplifier and the servo motor in a load-bearing place in
accordance with the Instruction Manual.
Do not get on or put heavy load on the equipment. Otherwise, it may cause injury.
Use the equipment within the specified environmental range. For the environment,
refer to section 1.3.
Provide an adequate protection to prevent screws and other conductive matter, oil
and other combustible matter from entering the servo amplifier.
Do not block the intake and exhaust areas of the servo amplifier. Otherwise, it
may cause a malfunction.
Do not drop or apply heavy impact on the servo amplifiers and the servo motors.
Otherwise, injury, malfunction, etc. may occur.
Do not install or operate the servo amplifier which have been damaged or have
any parts missing.
When the product has been stored for an extended period of time, contact your
local sales office.
When handling the servo amplifier, be careful about the edged parts such as
corners of the servo amplifier.
The servo amplifier must be installed in the metal cabinet.
When fumigants that contain halogen materials such as fluorine, chlorine,
bromine, and iodine are used for disinfecting and protecting wooden packaging
from insects, they cause malfunction when entering our products. Please take
necessary precautions to ensure that remaining materials from fumigant do not
enter our products, or treat packaging with methods other than fumigation (heat
method). Additionally, disinfect and protect wood from insects before packing
products.

2.1 Installation direction and clearances

CAUTION

The equipment must be installed in the specified direction. Otherwise, it may
cause a malfunction.
Leave specified clearances between the servo amplifier and the cabinet walls or
other equipment. Otherwise, it may cause a malfunction.

When using heat generating equipment such as the regenerative option, install them with full consideration
of heat generation so that the servo amplifier is not affected.
Install the servo amplifier on a perpendicular wall in the correct vertical direction.

«
...
30
31
32
33
34
...
»

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J4W2-0303B6

Бренд: 5Core Страницы: 2

Бренд: Warfedale Pro Страницы: 12

Бренд: Audeze Страницы: 16

Бренд: Transistor Страницы: 44

ProMedia DD-5.1

Бренд: Klipsch Страницы: 34

Бренд: AMC Страницы: 7

Бренд: icon Audio Страницы: 9

Бренд: Integra Страницы: 64

Бренд: Harman Kardon Страницы: 52

Phase Linear UPA224

Бренд: Audiovox Страницы: 29

Бренд: Max Страницы: 16

COMPETITION 12000.1D

Бренд: GAS Car Audio Страницы: 12

Бренд: thomann Страницы: 36

Бренд: GENZLER Страницы: 6

Бренд: GBC Страницы: 4

Бренд: SpeakerCraft Страницы: 7

Бренд: Parasound Страницы: 28

WORKINGMAN'S 10

Бренд: SWR Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды