Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 588

background image

5. PARAMETERS

5 - 41

No.

Symbol

Name and function

Initial
value

[unit]

Setting

range

Each/

Common

PC12

MO2

Analog monitor 2 offset
Set the offset voltage of MO2 (Analog monitor 2).
The parameter is available with MR-J4W2-0303B6 servo amplifiers.

0

[mV]

-9999

to

9999

Common

PC13 MOSDL Analog monitor - Feedback position output standard data - Low

Set a monitor output standard position (lower 4 digits) for the feedback position for
when selecting "Feedback position" for MO1 (Analog monitor 1) and MO2 (Analog
monitor 2).
Monitor output standard position = [Pr. PC14] setting × 10000 + [Pr. PC13] setting
The parameter is available with MR-J4W2-0303B6 servo amplifiers.

0

[pulse]

-9999

to

9999

Each

PC14 MOSDH Analog monitor - Feedback position output standard data - High

Set a monitor output standard position (higher 4 digits) for the feedback position for
when selecting "Feedback position" for MO1 (Analog monitor 1) and MO2 (Analog
monitor 2).
Monitor output standard position = [Pr. PC14] setting × 10000 + [Pr. PC13] setting
The parameter is available with MR-J4W2-0303B6 servo amplifiers.

0

[10000

pulses]

-9999

to

9999

Each

PC17 **COP4 Function selection C-4

Select a home position setting condition.

Refer to the Name
and function
column.

Each

Setting

digit

Explanation

Initial
value

_ _ _ x

Selection of home position setting condition
0: Need to pass servo motor Z-phase after power on
1: Not need to pass servo motor Z-phase after power on

0h

_ _ x _

Linear scale multipoint Z-phase input function selection
When two or more reference marks exist during the full
stroke of the linear encoder, set "1".
0: Disabled
1: Enabled
This parameter setting is used by servo amplifiers with
software version A5 or later.
For MR-J4W2-0303B6 servo amplifiers, this digit cannot be
used other than the initial value.

0h

_ x _ _

For manufacturer setting

0h

x _ _ _

0h

PC18

*COP5 Function selection C-5

Select an occurring condition of [AL. E9 Main circuit off warning].

Refer to Name
and function
column.

Common

Setting

digit

Explanation

Initial
value

_ _ _ x

For manufacturer setting

0h

_ _ x _

0h

_ x _ _

0h

x _ _ _

[AL. E9 Main circuit off warning] selection
0: Detection with ready-on and servo-on command
1: Detection with servo-on command

0h

«
...
136
137
138
139
140
...
»

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J4W2-0303B6

'65 TWIN REVERB

Бренд: Fender Страницы: 7

Ground Pounder GPV1000.2

Бренд: Crunch Страницы: 15

Бренд: Harman Kardon Страницы: 50

Бренд: DaytonAudio Страницы: 4

Бренд: Unika Страницы: 16

Бренд: Bugera Страницы: 15

Бренд: Pyle Pro Страницы: 6

Бренд: stellar labs Страницы: 7

Бренд: Ampetronic Страницы: 7

Бренд: Tokyo Страницы: 11

Бренд: Sonic Farm Страницы: 8

Бренд: Alecto Страницы: 40

Бренд: Parasound Страницы: 28

WORKINGMAN'S 10

Бренд: SWR Страницы: 24

REFERENCE 200.5 S2

Бренд: B&K Страницы: 12

C Series B-60 SST

Бренд: Bryston Страницы: 8

Ultra Fuzz UF-01

Бренд: Zoom Страницы: 16

Бренд: ORANGE Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды