Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 269 | Manualshive

Страница: 269 / 588

background image

11. OPTIONS AND PERIPHERAL EQUIPMENT

11 - 24

11.4 MR Configurator2

MR Configurator2 (SW1DNC-MRC2-_) uses the communication function of the servo amplifier to perform
parameter setting changes, graph display, test operation, etc. on a personal computer.

11.4.1 Specifications

Item Description

Project

Create/read/save/delete project, read/write other format, system setting, print

Parameter Parameter

setting

Monitor

Display all, I/O monitor, graph, ABS data display

Diagnosis

Alarm display, alarm onset data, drive recorder, no motor rotation, system configuration,
life diagnosis, machine diagnosis, fully closed loop diagnosis (Note 2), linear diagnosis
(Note 3)

Test mode

Jog mode (Note 4), positioning mode, motor-less operation (Note 1), DO forced output,
program operation, test mode information

Adjustment

One-touch tuning, tuning, machine analyzer

Others

Servo assistant, parameter setting range update, machine unit conversion setting, help
display

Note 1. The motor-less operation cannot be used in the fully closed loop control mode, linear servo motor control

mode, or DD motor control mode.

2. This is available only in the fully closed loop control mode.

3. This is available only in the linear servo motor control mode.

4. This is available in the standard control mode, fully closed loop control mode, and DD motor control mode.

«
...
267
268
269
270
271
...
»

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J4W2-0303B6

Бренд: LABTEC Страницы: 12

Бренд: Fender Страницы: 20

Бренд: W Audio Страницы: 20

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 35

Бренд: Yamaha Страницы: 20

Бренд: Yamaha Страницы: 8

Бренд: Monacor Страницы: 20

Бренд: SKP Pro Audio Страницы: 12

DANTE VIRGIL OB

Бренд: Glensound Страницы: 26

Бренд: Vanguard Страницы: 4

Бренд: PrimaLuna Страницы: 20

Бренд: Blackstar Страницы: 28

Бренд: Linn Страницы: 22

Бренд: Paradise Datacom Страницы: 82

Бренд: JB Systems Light Страницы: 11

Бренд: Flintec Страницы: 22

The Spell Booster

Бренд: Olsson Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды