Mitsubishi Electric MR-J4W2-0303B6 Скачать руководство пользователя страница 271 | Manualshive

Страница: 271 / 588

background image

11. OPTIONS AND PERIPHERAL EQUIPMENT

11 - 26

(2) Connection with servo amplifier

To USB

connector

USB cable

MR-J3USBCBL3M

(Option)

Personal computer

Servo amplifier

CN5

(Note)

Note. CN5 is located under the display cover.

11.4.3 Precautions for using USB communication function

Note the following to prevent an electric shock and malfunction of the servo amplifier.

(1) Power connection of personal computers

Connect your personal computer with the following procedures.

(a) When you use a personal computer with AC power supply

1) When using a personal computer with a three-core power plug or power plug with grounding wire,

use a three-pin socket or ground the grounding wire.

2) When your personal computer has two-core plug and has no grounding wire, connect the

personal computer to the servo amplifier with the following procedures.

a) Disconnect the power plug of the personal computer from an AC power socket.

b) Check that the power plug was disconnected and connect the device to the servo amplifier.

c) Connect the power plug of the personal computer to the AC power socket.

(b) When you use a personal computer with battery

You can use as it is.

(2) Connection with other devices using servo amplifier communication function

When the servo amplifier is charged with electricity due to connection with a personal computer and the
charged servo amplifier is connected with other devices, the servo amplifier or the connected devices
may malfunction. Connect the servo amplifier and other devices with the following procedures.

(a) Shut off the power of the device for connecting with the servo amplifier.

(b) Shut off the power of the servo amplifier which was connected with the personal computer and

check the charge lamp is off.

(c) Connect the device with the servo amplifier.

(d) Turn on the power of the servo amplifier and the device.

«
...
269
270
271
272
273
...
»

Содержание MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J4W2-0303B6

Бренд: Omega Engineering Страницы: 2

Бренд: Eclipse Страницы: 22

Бренд: Ecleree Страницы: 38

Бренд: Velleman Страницы: 29

Бренд: D.W. Fearn Страницы: 21

Бренд: L-Acoustics Страницы: 46

Бренд: L-Acoustics Страницы: 24

Бренд: dB Technologies Страницы: 133

Бренд: Wyred 4 Sound Страницы: 12

Бренд: Teac Страницы: 96

Бренд: C-COR Страницы: 172

Acoustic Box II

Бренд: Vintage Revolution Страницы: 17

Бренд: Supertech instruments Страницы: 6

Бренд: Rane Страницы: 19

Бренд: Sansui Страницы: 15

SILVER REFERENCE

Бренд: Trinity Страницы: 22

Бренд: Nova Страницы: 16

Бренд: Revox Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды