manualshive.com logo in svg

Lenze L-force 8400 Series, Справочное руководство, Страница: 274 / 1590

Поделиться
Скачать
Lenze L-force 8400 Series Скачать руководство пользователя страница 274

5

Motor control (MCTRL)

5.10

Parameterisable additional functions

274

Lenze · 8400 HighLine · Reference manual · DMS 12.0 EN · 06/2017 · TD23

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

5.10.6.2

Oscillation damping in the field weakening range

When the max. possible output voltage (full modulation) has been reached, a voltage dip in the DC

bus causes a voltage fluctuation in the motor. With load and during no-load operation this voltage

fluctuation can cause mechanical oscillations.
The "oscillation damping field weakening" adjustable in 

C00236

 serves to limit the maximum

output voltage. This can be used to always compensate voltage dips in the DC bus to the output

voltage (constant output voltage). This serves to prevent mechanical oscillations due to these

voltage dips.

• With the Lenze setting of 

C00236

 the limitation of the output voltage is set so that voltage dips 

in the DC bus in the output voltage for the single-phase and three-phase devices can largely be 

compensated so that no speed oscillations may be expected. Thus, an adaptation of 

C00236

 is 

not required in the majority of cases.

• Maximum output voltage to be reached with Lenze setting of 

C00236

:

• Single-phase  devices:  98.2 %
• Three-phase devices: 99.7 %

How to eliminate speed oscillations in the field weakening range:

1. Approach the area where the speed oscillations occur.
2. Reduce the speed oscillations by changing 

C00236

 step by step (increment 1).

3. These can be indicators for smooth running:

• Constant motor current characteristic
• Reduction of the mechanical oscillations in the bearing seat

Parameters

Info

Lenze setting

Value Unit

C00236

Oscillation damping field weakening

• Setting  "0" 

≡

 100 % output voltage can be reached

14

Note!

The limitation of the output voltage via 

C00236

 in the extreme field weakening range 

(high speeds) causes a reduction of the max. possible output torque (stalling torque).

• If the output torque to be reached in the extreme field weakening range is not 

sufficient (motor is stalling too early), reduce the setting in 

C00236

.

With servo control (SC), the Lenze setting of 

C00236

 should not be reduced. Otherwise 

the field weakening control could not work optimally anymore (the behaviour at high 

speeds may get worse). When servo control (SC) has been selected, the oscillation 

damping in 

C00236

 should never be set to "0".

Содержание L-force 8400 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов