Lenze L-force 8400 Series Скачать руководство пользователя страница 200

Страница: 200 / 1590

Motor control (MCTRL)

5.7

Sensorless vector control (SLVC)

200

Lenze · 8400 HighLine · Reference manual · DMS 12.0 EN · 06/2017 · TD23

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Speed controller reset time Ti

Apart from setting the P component,

C00071/1

provides the possibility to take influence on the I

component of the PI controller.



Tip!

Value range recommended by Lenze for the setting of the reset time:
Ti = 20 ms … 150 ms

5.7.4.3

Optimising dynamic performance and field weakening behaviour

In the Lenze setting, the torque controller has been preset in such a way that robust and stable

operation with a moderate dynamic response is enabled over the entire speed range. Retrospective

optimisation of the controller parameters is not necessary.

A greater dynamic performance of the sensorless vector control can be achieved by reducing time

constant Ti of the speed controller (

C00074/2

A greater dynamic performance of the field weakening function can be achieved by setting a time

constant

≤

15 ms. This means for actual speeds above rated speed a better torque-speed-

characteristic in the field weakening range:

[5-11] Speed / torque characteristic diagram in the field weakening range

• For Ti > 15 ms (see



), the actual speed value slightly drops in the field weakening range if the

load torque increases in the motor mode.

• For Ti

≤

15 ms (see



), the speed remains stable in the field weakening range if the torque is

within the M/n characteristic field highlighted in grey.



Tip!

For applications with high dynamic performance and speed/torque accuracy requirements

in the field weakening range, we recommend a time constant Ti

≤

15 ms.

In this case, the maximum torque should be limited via the

nTorqueMotLimit_a

and

nTorqueGenLimit_a

process input signals to 1.5 x M

to ensure stable operation in the field

weakening range.

Parameters

Info

Lenze setting

Value Unit

C00073/2

SLVC: Vp torque controller

1.25

C00074/2

SLVC: Ti torque controller

30 ms



Torque controller time constant Ti > 15 ms



Torque controller time constant Ti

≤

15 ms

Содержание L-force 8400 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание L-force 8400 Series

Отзывы:

Lenze L-force 8400 Series, Справочное руководство, Страница: 200 / 1590

Результаты поиска

Содержание L-force 8400 Series

Отзывы: