Lenze L-force 8400 Series Скачать руководство пользователя страница 1151

Страница: 1151 / 1590

Lenze · 8400 HighLine · Reference manual · DMS 12.0 EN · 06/2017 · TD23

1151

Parameter reference

15.2

Parameter list

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

C02868

Parameter | Name:

C02868 | Setting of compatibility

Data type: UNSIGNED_32

Index: 21707

= 54CB

From version 16.00.00

This parameter serves to activate corrections and optimisations in various functions of the inverter. The activation

causes a deviation of the respective functionality from the previous firmware versions!

In each case, the changed functionality has to be checked after the activation took place.

For a detailed explanation, the version information in the AKB has to be used.

Setting range

(min. hex value | max. hex value)

0x00000000

0xFFFFFFFF

Value is bit-coded:

Info

Bit 0 xx.01: MCK stop ramp opt.

≡

(Maloperation): Profile stop activation with

corresponding machine and profile data causes a

rotation in the opposite direction and setpoint

oscillations around zero speed.

≡

(Correction): Corrected traversing of stop ramp may

reduce the stopping times.

Bit 1 xx.02: MCK deceleration ramp opt.

≡

(Maloperation): When corresponding profile

parameters are entered, an impermissible jerk is caused

during the braking phase when entering into the target

position within a traversing profile.

≡

(Correction): Depending on the profile data

constellation, corrected traversing extends the

respective traversing process towards the target

position.

Bit 2 xx.03: MCK Overchange opt.

≡

(error CK10 occurs):

• Traversing profile with final speed

≠

0 needs a

reversing process after reaching the target position.

• Parameterised final speed in profile parameters

cannot be reached at the target approach (final speed

too high).

• Position target cannot be approached if

• the initial speed of the traversing profile

final

speed

≡

(Correction): Ck10 does not occur anymore in this

setting.

• Travelling profiles with final speed is always executed

in such a way that the target position will be reached

if the parameterised final speed is neglected.

• Expected Ck10 errors do not occur anymore,

traversing blocks are executed.

Bit 3 xx.04: MCK PosFollower TargetPos

≡

(Previous procedure):

• No information on target position

LS_MotionControlKernel.dnPosTarget_p

when a

synchronisation process is started in the position

follower mode. Previous display of the target position

remains unchanged.

≡

Display of the target position and thus the rejection

of the previously saved values in

LS_MotionControlKernel.dnPosTarget_p

Bit 4 xx.05: MCK speed, change in op.

mode, opt.

From version 17.00.00 onwards

≡

(Previous procedure):

• The change from "StandBy" mode to a different

operating mode (except for "SpeedFollower") causes

the speed to jump to 0 if

C02611/51

LS_MotorInterface.nHlgSetValue_a

is set.

≡

Instead of a speed jump, the "Stop" ramp is used to

decelerate the motor to standstill. This applies to the

state transition from "StandBy" to "Homing",

"ManualJog" or "Stop" if no further actions take place in

the new operating mode.

«
...
1149
1150
1151
1152
1153
...
»

Содержание L-force 8400 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание L-force 8400 Series

Отзывы:

Lenze L-force 8400 Series, Справочное руководство, Страница: 1151 / 1590

Результаты поиска

Содержание L-force 8400 Series

Отзывы: