Canon IMAGERUNNER 7095 PRINTER, Руководство по обслуживанию

Страница: 455 / 615

Chapter 16
16-21
0057 1st sheet pre-
reversal pickup
delay S1 The 1st sheet is identified as a pre-reversal pickup delay jam (0017).
0058 1st sheet pre-
reversal pickup
stationary 1 S1,PI4 The 1st sheet is identified as a pre-reversal pickup stationary 1 jam
(0018).
0059 1st sheet pre-
reversal pickup
stationary 2 S1,PI4 The 1st sheet is identified as a pre-reversal pickup stationary 2 jam
(0019).
0060 1st sheet reversal
pickup delay S2 The 1st sheet is identified as a reversal pickup delay (0020).
0061 1st sheet reversal
pickup stationary S2 The 1st sheet is identified as a reversal pickup stationary jam (0021).
0062 1st sheet pickup
lead edge skew S4,S5 The 1st sheet is identified as a pickup lead edge skew jam (0022).
0063 1st sheet pickup trail
edge skew S4,S5 The 1st sheet is identified as a pickup trail edge skew jam (0023).
0064 1st sheet pickup
fault 1 S1 A pickup NG1 condition (0024) has occurred on the 1st sheet.
0065 1st sheet pickup
fault 2 S3,S2 A pickup NG1 condition (0025) has occurred on the 1st sheet.
0066 1st sheet reversal
pickup trail edge
skew S4,S5 A reversal pickup trail edge skew condition (0026) has occurred on the
1st sheet.
0067 1st sheet reversal
pickup NG1 PI4 The 1st sheet is identified as a reversal pickup fault 1 jam (0027).
0071 timing fault 1 - The software control mechanism has failed.
0072 timing fault 2 - In copyboard mode, an original has been read and moved to and stopped
at the right side of the platen roller; however, the preceding original has
not been delayed.
0073 illegal size S3 At time of LDR stream reading, the post-registration sensor detects the
original after it has been moved a specific distance (30 mm) from the wait
position.
0074 manual feed original
size error S9,S1 At time of manual feed, the reversal sensor detects an original while the
manual registration roller sensor also detects an original.
0075 image lead edge
position error S7 At time of stream reading, no change has occurred in the read position in
response to a request for a change.
0076 1st sheet image lead
edge position error S7 The 1st sheet is identified as having an image lead edge position error
(0075).
0077 belt speed setting
error PI1 The speed setting of the belt motor is below the minimum speed (100
mm/sec) or above the maximum speed (700 mm/sec).
0078 belt speed switch-
over error PI1 When the belt motor speed is switched over, the belt motor is not moving
at a constant speed.
0079 belt status error PI1 At time of switch-over, the state is not any of the following: acceleration,
constant speed rotation, deceleration.
0080 image lead edge
output timing error S2,S3,SW3
01 At time of stream reading, the image lead edge signal is generated in the
course of acceleration while a move is made from the wait position to the
image lead edge position.
0081 reversal speed
setting error PI5 The speed setting of the reversal motor is below the minimum speed (100
mm/sec) or above the maximum speed (700 mm/sec).
0082 reversal speed
switch-over error PI5 At time of switching over the reversal motor speed, the reversal motor is
not rotating at a constant speed.
0083 reversal status error PI5 At time of switch-over, the state of the reversal motor is not any of the
following: acceleration, constant speed, deceleration.
0084 last original error PI1 A belt motor error occurs while the last original is being discharged by
the platen roller or being moved.
Code Sensor type Sensor No. Description