Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 210

background image

3-10

Removing Top-Side

Components

A. Valve Covers
B. Cylinder Heads



NOTE: Remove the spark plugs and timing

inspection plug (A); then using the recoil starter,
rotate the crankshaft to top-dead-center (TDC) of
the compression stroke of the front cylinder. TF is
top-dead-center front.

KX247

ATV2057A

1. Remove the two tappet covers. Account for two

gasket rings.

2. Remove the cap screws (A) securing the front

valve cover to the head; then remove the front

valve cover (B).

ATV2065



NOTE: Leave the camshaft and camshaft chain

tensioner installed until the rear rocker case is
removed or the cam chain will have to be sup-
ported while rotating the crankshaft.

3. Rotate the crankshaft counterclockwise to position

the rear cylinder at TDC on the compression

stroke; then remove the two tappet covers.

Account for two gasket rings. TR is

top-dead-center rear.

ATV2058A

4. Remove the cap screws (A) securing the rear valve

cover to the head; then remove the rear valve

cover (B).

ATV2066

5. Remove front and rear camshaft chain tensioners

by first removing the spring cap (D). Account for

one washer (C), one spring (B), and one guide rod

(A) for each tensioner.

! CAUTION

Be sure the crankshaft is on TDC of the
compression stroke of the front cylinder or valve
damage could occur.

«
...
37
38
39
40
41
...
»

Содержание 650 Twin2004



















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 650 Twin2004

Sportsman 9921483

Бренд: Polaris Страницы: 207

Бренд: Cushman Страницы: 71

Бренд: wsm Страницы: 25

TOURINO PICK-UP

Бренд: Cramer Страницы: 16

Бренд: Primo Water Страницы: 12

Бренд: Foldy Страницы: 44

Бренд: Morooka Страницы: 134

Бренд: Can-Am Страницы: 152

Бренд: Ultra-tow Страницы: 8

Бренд: Ultra-tow Страницы: 9

Бренд: PRONAR Страницы: 25

Бренд: PRONAR Страницы: 150

Sportsman 800 EFI

Бренд: Polaris Страницы: 388

Sportsman 850 2014

Бренд: Polaris Страницы: 154

Бренд: E-Z-GO Страницы: 74

Бренд: Palms Страницы: 19

RECOIL iS CREW 2015

Бренд: Bad Boy Страницы: 60

Бренд: Mahindra Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды