Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 193

Страница: 193 / 210

9-9

14.

Mode Button

— Used (in conjunction with the

Odometer/Trip Meters/Hour Meter) to shift the

odometer/trip meters/hour meter display through

the four modes: odometer, trip meter (A), trip

meter (B), and hour meter.

REPLACING SPEEDOMETER

To replace the speedometer, use the following proce-

dure.

1. Remove the four nylon fasteners securing the

instrument pod; then remove the ignition switch

retaining nut.

2. Remove the front rack and front fenders; then dis-

connect the multi-pin connector.

3. Remove the three nuts securing the mounting

studs; then remove the speedometer.

4. Route the new wiring harness down through the

opening; then mount the speedometer and secure

with the three nuts; then connect the multi-pin

connector.

5. Install the front fenders and front rack; then install

the instrument pod and secure with the nylon fas-

teners.

6. Secure the ignition switch with the retaining nut.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды