Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 180

Страница: 180 / 210

8-14

Footrests

REMOVING

1. Remove the cap screws securing the fender

extension to the footrest. Account for all cap

screws and one nut.



NOTE: It will be easiest to remove the front inner

cap screw by removing the nut from inside the
wheel well.

2. On the right-side footrest, disconnect the foot

brake switch from the main wiring harness.

3. Remove the cap screws securing the footrest to the

frame; then remove the footrest.



NOTE: On the right-side footrest, it will be neces-

sary to remove the foot brake cable from the brake
pedal.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean the footrest in parts-cleaning solvent.

2. Inspect the footrest weldments for cracks or

unusual bends.

3. Inspect all tubing for cracks or unusual bends.

INSTALLING

1. Connect the foot brake cable to the brake pedal

(right-side footrest).

2. Place the footrest into position on the frame and

loosely secure with the four cap screws.

3. Secure the fender extension to the footrest with

existing hardware. Tighten securely.

4. Tighten the 10 mm footrest cap screws (from step

2) to 5.5 kg-m (40 ft-lb); then tighten the 8 mm

cap screws (from step 2) to 2.8 kg-m (20 ft-lb).

5. Connect the foot brake switch to the main wiring

harness. Ensure that the harness is properly

secured to the frame and away from any moving

parts.

Belly Panel

REMOVING

1. Remove the machine screws and shoulder washers

securing the belly panel to the underside of the

frame.

2. Remove the belly panel.

INSTALLING

1. Place the belly panel into position on the underside

of the frame.

2. Install the machine screws and shoulder washers.

Tighten securely.

Exhaust System

REMOVING MUFFLER

1. Remove the cap screws securing the muffler to the

frame and account for all mounting hardware.

2. Loosen the clamp at the muffler/exhaust pipe

juncture; then remove the nuts securing the rear

exhaust pipe to the cylinder and remove the

muffler.

CH056D

INSPECTING MUFFLER



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Inspect muffler externally for cracks, holes, and

dents.

2. Inspect the muffler internally by shaking the

muffler back and forth and listening for rattles or

loose debris inside the muffler.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды