Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 191

Страница: 191 / 210

9-7

0739-083

REMOVING

1. Remove the seat (see Section 8).

2. Remove the three machine screws securing the

left-side panel to the frame and rear fender; then

remove the left-side panel.

3. Remove the E-clip securing the shift rod to the

engine shift arm.

KX057

4. Remove the three machine screws securing the

gear shift linkage cover to the fender and remove

the cover.



NOTE: The cover is located inside the left-front

wheel well.

CC851

5. Remove the axle and nut securing the shift lever to

the upper shift arm; then remove the shift lever.

Account for the spring and two O-rings on the

axle.

6. Using two open-end wrenches, remove the lock

nut (B) securing the shift rod to the upper shift

arm. Remove the shift rod and discard the lock

nut.

AF941A



NOTE: Never reuse a lock nut. Once a lock nut

has been removed, it must be replaced with a new
lock nut.

INSTALLING

1. Place the shift rod into position on the engine shift

arm and secure with the existing E-clip.

KX057

2. Using a new lock nut, secure the shift rod to the

upper shift arm; then using two open-end

wrenches, tighten securely.

AF941A

KEY

1. Nut
2. Cap Screw
3. Axle
4. Lever
5. O-Ring
6. O-Ring
7. Washer
8. Spring
9. Axle

10. Handle
11. Clip
12. Linkage
13. Rod End
14. Nut
15. Bushing
16. Washer
17. E-Ring
18. Plate

19. Shield
20. Screw
21. Screw
22. Shift Arm
23. Cap Screw

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды