Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 58

Страница: 58 / 210

3-29

KX286

3. Place the spider wrench (A) on the spider (B) and

tighten the bolt (C); then turn the wrench

clockwise and remove the spider with the movable

sheave.

KX287

4. Remove the shoes (B), nuts (C), ramp weight pins

(D), and ramp weights (E) from the spider (A);

then clean all parts thoroughly in a high

flash-point solvent.

ATV2071A

Inspecting

1. Inspect the sheave faces (A) for cracks, galling, or

hollowing; then check all bushings (B).

KX288

KX289A

KX290A

2. Inspect spider shoes (A) for wear or damage. If

any are damaged, replace the complete set.

! WARNING

Inspect all rotating parts carefully for cracks, loose
bolts, chips, or nicks. Clutches and driven pulleys
rotate at high speeds and can break up with explo-
sive force causing severe injury or death.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды