Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 82

Страница: 82 / 210

3-53

KX130

13. Connect the four disconnect plugs as shown; then

connect the battery positive cable and starter lead

to the starter relay.

KX074

14. Connect the starter cable to the starter lug and

tighten securely.

15. Connect the alternator and pick-up coil leads; then

attach the reverse indicator lead and neutral

indicator lead to the switches.

KX075B

16. Connect the speed sensor, forward/reverse sensor

lead, and oil pressure warning lead; then connect

the drive belt failure detector lead and the engine

brake control servo lead to the main harness.

Connect the spark plug wires.

17. Remove the tape from the carburetor inlets

checking for any foreign material; then using red

Loctite #271, install the lower air cleaner housing

and tighten the mounting screws securely.

18. Install the air filter and air filter cover.

KX119

KX118

19. Install the left footrest; then tighten the 10 mm cap

screws to 5.5 kg-m (40 ft-lb) and the 8 mm cap

screws to 2.8 kg-m (20 ft-lb).

20. Install all fenders, side panels, and racks that were

removed; then install the storage compartment

cover.

21. Install the battery by connecting the positive cable

first; then connecting the negative cable.

22. Install the seat making sure it is properly secured.

23. Fill with recommended oil and coolant. See

Section 2.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды