Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 120

Страница: 120 / 210

5-19

ATV2123

5. Connect a signal oscillator (A) to the battery

negative post and the output to terminal (13); then

set the oscillator frequency to 620 Hz. The

speedometer should read approximately 40 mph.

ATV2208C

6. Leave the wires connected as in step 5 and press

the MODE button (A) to cycle to the odometer

(B); then increase the frequency of the oscillator.

The odometer should start to count faster.

ATV2125

7. Depress the MODE button (A) and cycle to trip

meters A and B (B); then check the function of

both trip meters in the same manner as the

odometer. Disconnect the oscillator.

ATV2126

8. Connect the wires in the same manner as step 1;

the first segment LCD (A) should flash.

ATV2127

9. Connect a jumper wire from the negative battery

terminal to terminal (3) on the connector. When

connected, one segment in the fuel gauge should

appear every 15 seconds.

ATV2208D

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды