Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 29

Страница: 29 / 210

2-20

2. If belt width is below the service limit of 28.8 mm

(1.13 in.) or there is damage to the belt, it must be

replaced.

INSTALLING



NOTE: Be sure to install the belt in the same

direction as originally installed. When installing a
new belt, direct the top of the lettering (A) toward
the engine.

1. Loop the belt (B) over the driven pulley (C); then

install the drive cluch and tighten to spcifications.

KX232



NOTE: Make sure the belt is at the top of the

driven pulley (A) before checking belt deflection.

KX233

2. Place a straightedge (B) on top of the belt between

the drive clutch (C) and the driven pulley (D); then

using a ruler, check the belt deflection (A). Use a

maximum force of 6 kg (13 lb) on the ruler. Stan-

dard belt deflection is 22-27 mm (0.87-1.06 in.). If

belt deflection is out of specifications, see Section

3, Right-Side Components.

ATV2061

3. Check the position of the Belt Failure Detection

Switch (A) and reset to the ON position (B).

ATV2062A



NOTE: If the Belt Failure Detection Switch has

been tripped to the OFF position, the V-belt cover
and switch assembly must be replaced and the
V-Belt Failure Mode Clearing procedure (see Sec-
tion 5) must be performed.

4. Install the cover seal into the V-belt cover with the

glue joint (A) as shown; then install the V-belt

cover and tighten the cap screws to specifications.

ATV2063

5. Connect the actuator lead and the Belt Failure

Detection Switch lead; then install the air duct and

secure with the clamps.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды