Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 104

Страница: 104 / 210

5-3

Accessory

Receptacle/Connector



NOTE: This test procedure is for either the

receptacle or the connector.

VOLTAGE

1. Set the meter selector to the D.C. Voltage position.

2. Connect the red tester lead to the red/white wire or

the positive connector; then connect the black

tester lead to ground.

AR606D

3. The meter must show battery voltage.



NOTE: If the meter shows no battery voltage,

troubleshoot the battery, fuse, receptacle, connec-
tor, or the main wiring harness.

Brakelight Switch

(Auxiliary)

The switch connector is the two-prong connector on

the right side of the engine directly above the brake

cable adjuster.



NOTE: The ignition switch must be in the ON

position.

VOLTAGE

(Wiring Harness Side)

1. Set the meter selector to the D.C. Voltage position.

2. Connect the red tester to the orange wire; then

connect the black tester lead to ground.

AR627D

3. The meter must show battery voltage.



NOTE: If the meter shows no battery voltage,

troubleshoot the battery, fuse, switch, or the main
wiring harness.



NOTE: If the meter shows battery voltage, the

main wiring harness is good; proceed to test the
switch/component, the connector, and the switch
wiring harness for resistance.

RESISTANCE

(Switch Connector)

1. Set the meter selector to the OHMS position.

2. Connect the red tester lead to one black wire; then

connect the black tester lead to the other black

wire.

AR626D

3. When the brake pedal is depressed, the meter must

show less than 1 ohm.



NOTE: If the meter shows more than 1 ohm of

r e s i s t a n c e , t r o u b l e s h o o t o r r e p l a c e t h e
switch/component, the connector, or the switch
wiring harness.

! CAUTION

Always disconnect the battery when performing
resistance tests to avoid damaging the
multimeter.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды