Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 210

background image

4-9

4

Gas Tank

0739-082

REMOVING

1. Turn the gas tank valve to the OFF position.

2. Remove the seat.

3. Remove the rear rack and fenders.

4. Disconnect the hose from the fuel pump to the

tank valve at the fuel pump.

5. Remove the cap screws securing the gas tank to

the frame.

6. Disconnect the fuel pump/fuel gauge connector;

then remove the gas tank.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all gas tank components with parts-cleaning

solvent.

2. Inspect all hoses for cracks or leaks.

3. Inspect tank cap and tank for leaks, holes, and

damaged threads.

INSTALLING

1. Place the gas tank into position in the frame; then

install the cap screws. Tighten securely.

2. Connect the fuel hose from the gas tank valve;

then connect the fuel pump/fuel gauge connector.

3. Install the vent hose; then fill the gas tank with

gasoline.

4. Turn the gas tank valve to the ON position and

inspect for leakage.

5. Install the rear fenders and rack; then install the

seat making sure it latches securely.

Gas Tank Valve

The ATV has a valve separate from the gas tank. There

are two positions: ON and OFF.

KX030

In the OFF position, the valve will not allow gasoline

to flow to the carburetor. In the ON position (the nor-

mal operating position), gasoline is pumped from the

tank to the carburetor. The ignition switch must be in

the ON position to activate the electric fuel pump.

When turning the valve to either of the two positions,

be sure the indicator is pointed directly at the position

desired.

REMOVING/INSPECTING

1. Remove the gas hose from the valve by releasing

the spring clamp.

2. Remove the two screws securing the valve; then

remove the valve.

! WARNING

Whenever any maintenance or inspection is made
on the fuel system during which there may be fuel
leakage, there should be no welding, smoking,
open flames, etc., in the area.

KEY

1. Gas Tank
2. Sleeve
3. Tank Cap
4. Gasket
5. Screw
6. Fuel Pump
7. Damper
8. Insert
9. Nut

10. Cap Screw

11. Grommet
12. Hose Clamp
13. Fuel Hose
14. Breather
15. Shoulder Screw
16. Nut w/Washer
17. Grommet
18. Check Valve
19. Cable Tie
20. Shield
21. Shield
22. Shield
23. Tank Valve Assy
24. O-Ring
25. Screw
26. Screw

«
...
90
91
92
93
94
...
»

Содержание 650 Twin2004



















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 650 Twin2004

Бренд: ODES Страницы: 92

Бренд: IceCar Страницы: 37

Бренд: Razor Страницы: 2

CU-48 OFF-ROAD SERIES

Бренд: Crown Страницы: 8

Бренд: Arctic Cat Страницы: 123

Бренд: Baja motorsports Страницы: 18

Бренд: BOMBARDIER Страницы: 129

Бренд: Kazuma Страницы: 25

Бренд: Can-Am Страницы: 144

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 130

Бренд: Yamaha Страницы: 136

Бренд: Yamaha Страницы: 132

YFB250K Timberwolf

Бренд: Yamaha Страницы: 159

Бренд: Yamaha Страницы: 214

Бренд: Kinroad Страницы: 37

Бренд: Costway Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды