Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 59

Страница: 59 / 210

3-30

KX291

3. Inspect the ramp weights (A) and pins (B) in the

movable sheave. Replace any worn parts.

KX292

4. Inspect the rollers (A) and washers (C) in the

spider. If they are worn, replace the spider

assembly (B).

KX293

Assembling

1. Install the ramp weights (A) and tighten nuts (B)

to specifications; then check that the ramp weights

swing freely.

KX294

2. Place the fixed sheave on the clutch holder; then

install the movable sheave, spider (A) and shoes

(B) aligning the arrow (C) with the arrow (D) on

the movable sheave.

KX295

3. Install the spider wrench (A) on the spider (B) and

tighten bolt (C); then tighten spider

counterclockwise to specifications.

KX296

4. Install the spring spacer in the spider; then install

the spring (A) in the spider groove.

5. Install the alignment pins (C); then install the

clutch cover aligning the arrows (B) on the clutch

cover and spider. Tighten to specifications.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды