Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 23

Страница: 23 / 210

2-14

Stop the ATV completely and shift the transmission

into the R position. The reverse gear indicator light

should be illuminated.

If the reverse lever light does not illuminate when

shifted to the reverse position, the switch may be

faulty, the fuse may be blown, the bulb may be faulty,

a connection may be loose or corroded, or the lever

may need adjusting. To adjust, proceed to Adjusting

Shift Lever.

ADJUSTING SHIFT LEVER

0739-083

1. Place the shift lever in the R position.

2. Remove the seat; then remove the storage com-

partment cover housing.

3. Remove the left upper body side panel.

4. Loosen shift rod end jam nut (A).

AF941A

5. Using two open-end wrenches, remove lock nut

(B) securing the shift rod to the upper shift axle.

Discard the lock nut.



NOTE: Never reuse a lock nut. Once a lock nut

has been removed, it must be replaced with a new
lock nut.

6. Push the shifter arm to the most forward position

(reverse).

KX057

! WARNING

Never shift the ATV into reverse gear when the ATV
is moving as it could cause the ATV to stop sud-
denly throwing the operator from the ATV.

KEY

1. Nut
2. Cap Screw
3. Axle
4. Lever
5. O-Ring
6. O-Ring
7. Washer
8. Spring
9. Axle

10. Handle
11. Push Clip
12. Linkage
13. Rod End
14. Nut
15. Bushing
16. Washer
17. E-Ring
18. Plate
19. Shield
20. Machine Screw
21. Self-Tapping Screw
22. Shift Arm
23. Cap Screw

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды