Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 54

Страница: 54 / 210

3-25

CC283D

2. Rotate the camshaft and note runout; maximum

tolerance must not exceed specifications.

Measuring Camshaft Lobe Height

1. Using a calipers, measure each cam lobe height.

ATV1013A

2. The lobe heights must not exceed minimum

specifications.

Inspecting Camshaft Bearing
Journal

1. Inspect the bearing journal for scoring, seizure

marks, or pitting.

2. If excessive scoring, seizure marks, or pitting is

found, the cylinder head assembly must be

replaced.

Measuring Camshaft to
Cylinder Head Clearance

1. Remove the adjuster screws and jam nuts.

CC005D

2. Place a strip of plastigauge in each of the camshaft

lands in the cylinder head.

3. Place the valve cover on the cylinder head and

secure with the valve cover cap screws. Tighten in

correct sequence to specifications.

ATV2070



NOTE: Tighten cap screws 1-4 with washers to

0.9 kg-m (78 in.-lb), cap screws 5-6 to 1.0 kg-m (87
in.-lb), and cap screws (A) to 1.0 kg-m (87 in.-lb).



NOTE: Do not rotate the camshaft when measur-

ing clearance.

4. Remove the cap screws securing the valve cover to

the cylinder; then remove the valve cover and

camshaft.

5. Match the width of the plastigauge with the chart

found on the plastigauge packaging to determine

camshaft to cylinder head and valve cover

clearance.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды