Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 93

Страница: 93 / 210

4-10

KX027

3. Inspect for and remove any obstructions in the

valve.

INSTALLING

1. Place the valve on the frame and secure with the

screws. Tighten securely.

2. Install the gas hoses onto the valve with the spring

clamps.

Oil Flow Chart

Gas/Vent Hoses

Replace the gas hose every two years. Damage from

aging may not always be visible. Do not bend or

obstruct the routing of the carburetor vent hose. Make

certain that the vent hose is securely connected to the

carburetor and the opposite end is always open.

Electric Fuel Pump

The electric fuel pump and fuel level sensor are a

non-serviceable assembly. If either fails, the fuel pump

assembly must be replaced.



NOTE: For testing the fuel pump, see Testing

Electric Fuel Pump in this section.

ATV2112

KEY

1. Oil Screen
2. Oil Pump
3. Relief Valve
4. Oil Pressure Switch
5. Oil Filter
6. Oil Pipe
7. Crankshaft
8. Rear Cylinder Head
9. Rear Camshaft

10. Transmission Idle Shaft
11. Transmission Driveshaft
12. Front Cylinder Head
13. Front Camshaft

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды