Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 18

Страница: 18 / 210

2-9

Gas/Vent Hoses

Replace the gas hose every two years. Damage from

aging may not always be visible. Do not bend or

obstruct the routing of the carburetor vent hose. Make

certain that the vent hose is securely connected to the

carburetor and the opposite end is always open.

Adjusting Throttle

Cable

To adjust the throttle cable free-play, follow this pro-

cedure.

1. Slide the rubber boot away; then loosen the jam

nut from the throttle cable adjuster.

AL611D

2. Slide the rubber boot away and turn the adjuster

until the throttle cable has proper free-play of 3-6

mm (1/8 - 1/4 in.) at the lever.

ATV-0047

3. Tighten the jam nut against the throttle cable

adjuster securely; then slide the rubber boot over

the adjuster.

Adjusting Engine RPM

(Idle)

To properly adjust the idle RPM, a tachometer is nec-

essary. To adjust idle RPM, use the following proce-

dure.

1. With the transmission in neutral, start the engine

and warm it up to normal operating temperature.

2. Turn the idle adjustment screw clockwise one turn

past the recommended RPM setting; then turn it

counterclockwise to 1050-1150 RPM.

KX029A

Engine/Transmission

Oil - Filter

OIL - FILTER

Change the engine oil and oil filter at the scheduled

intervals. The engine should always be warm when the

oil is changed so the oil will drain easily and com-

pletely.

1. Park the ATV on level ground.

2. Loosen the oil level stick/filler plug.

! WARNING

Adjust the idle to the correct RPM. Make sure the
engine is at normal operating temperature before
adjusting the idle RPM.

Adjustment Screw

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды