Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 152

Страница: 152 / 210

6-24

3. Remove the two cap screws and lock nuts securing

the rear gear case to the frame; then move the gear

case to the rear sufficiently to disengage the

splined yoke from the rear output spline shaft.

Remove through the left frame opening.

KX078

INSTALLING

1. Slide the gear case into position through the left

side of the frame; then move the gear case to the

rear sufficiently to engage the splined yoke with

the splined rear output shaft.

2. Position the gear case so the mounting cap screws

can be installed; then with washers and new lock

nuts, tighten to 4.3-5.3 kg-m (31-38 ft-lb).



NOTE: If a new gear housing is being installed,

tighten the cap screws to 5.1-6.3 kg-m (37-45.5
ft-lb).

3. Install the rear drive axles (see Drive Axles in this

section).

4. Install the left-side rear A-arms (see Rear A-Arms

in Section 7).

Hub



NOTE: The hubs on this ATV have replaceable

wheel studs. These studs are easily changed with-
out removing the hub.

REPLACING WHEEL STUDS

1. Support the ATV on adequate stands or a lift; then

remove the applicable wheel.

2. Thread a lug nut onto the stud; then using a

hammer drive the stud out of the hub.

KX132



NOTE: If the threads are damaged, simply drive

the stud out without threading on a nut.

3. Insert a new stud in the hub; then install a lug nut

with the flat side next to the hub and using an air

wrench, draw the stud into the hub.



NOTE: Do not reuse wheel studs once removed.

REMOVING

1. Secure the ATV on a support stand to elevate the

wheel; then remove the wheel.

2. Remove the cotter pin from the nut.



NOTE: During assembly, new cotter pins should

be installed.

KX041



AT THIS POINT

For servicing the input shaft, pinion gear, needle
bearing, and axle seal, see Front Differential in
this section.

! WARNING

If any studs are loose in the hub, the hub must be
replaced. Loose studs will not hold the wheel
securely to the hub and hub breakage or wheel loss
could occur causing loss of control, injury, or
death.

! WARNING

Make sure the ATV is solidly supported on the sup-
port stand to avoid injury.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды