Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 33

Страница: 33 / 210

3-4

KX101A

8. Remove the rear V-belt cooling boot; then

disconnect the belt failure detection lead (D) and

the engine brake control actuator lead (C).

KX234A

9. Disconnect the alternator lead connector (A); then

disconnect the pick-up coil lead (B) and the speed

sensor connector (E).

10. Remove the neutral position connector (F) and

reverse position connector (H); then disconnect

the forward and reverse detection sensor lead (G).

KX075A

11. Remove the front and rear spark plug caps; then

remove the oil pressure sending unit lead (I).

KX046A

12. Remove the left footrest assembly.

KX104

13. Loosen the carburetor intake boot clamp (J); then

remove the two coolant hoses (K).

KX025D

14. Remove the throttle cover from the front

carburetor; then disconnect the throttle cable.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды