Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 28

Страница: 28 / 210

2-19

REMOVING

1. Make sure that the ignition switch is in the off

position; then remove the clamps (A) and air duct

(B).

KX229

2. Remove the actuator lead (A) and the Belt Failure

Detection Switch lead (B); then remove the cap

screws (C) securing the V-belt cover. Remove the

cover (D).

KX230

3. Remove the three cover bolts (B) in the positions

shown and install an appropriate drive clutch

holder (A) as shown. Note the holder’s relative

position to the arrow mark (D).

KX231

4. Remove the drive clutch cap screw (C) (left-hand

threads) and account for two washers and a

stepped washer.

5. Remove the drive clutch (C) from the crankshaft

using an appropriate clutch puller tool (B) and

turning it clockwise while holding the drive clutch

with the drive clutch holder (A).

ATV2059



NOTE: Before removing the belt, note the mark-

ings (A) (or mark the belt using tape or marker) in
order to reinstall in the same direction as previ-
ously installed.

6. Lift the belt (B) off the driven pulley (C).

KX232



NOTE: Inspection of the belt is required every

100 hours or 1100 miles. More frequent inspection
is required if the ATV is operated in adverse condi-
tions.

INSPECTING

1. Measure the belt width (A) at several locations

using a pair of suitable straightedges (B).

ATV2060

! CAUTION

Be sure to install the three bolts in the specified
positions or the tapped holes will be damaged.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды