Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 177

Страница: 177 / 210

8-11

Front Bumper

Assembly

REMOVING



NOTE: Remove the headlights with the front

bumper.

1. Remove the main wiring harness connectors from

the four headlights.

2. Remove the two screws securing the grille to the

front bumper.

3. Remove the two push nuts securing the fender

extension to the front bumper. Push the fender

extension studs out of the front bumper.

CC856

4. Remove the four cap screws securing the front

skid plate to the front bumper.

5. Remove the two cap screws securing the front

bumper to the frame.

CC858

6. Remove the two cap screws securing the front

bumper to the front bumper supports.

CC857

7. Remove the front bumper with headlights.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all bumper components with parts-cleaning

solvent.

2. Inspect all welds for cracking or bending.

3. Inspect threaded areas of all mounting bosses for

stripping.

4. Inspect the wiring harness and headlights for

damage.

5. Inspect the screen for damage or air-flow

obstructions.

INSTALLING

1. Place the front bumper assembly into position on

the frame and secure with four cap screws.

Tighten securely.

2. Secure the front skid plate to the front bumper

with the four cap screws. Tighten securely.

3. Place the two fender extension studs through the

front bumper and secure with the existing push

nuts.

CC856

4. Position the grille in the front bumper and secure.

5. Connect the wiring to each of the headlights.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды