Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 105

Страница: 105 / 210

5-4

Brakelight Switch

(Handlebar Control)

The switch connector is the two-prong black connector

in front of the steering post. To access the connector,

the front rack and front fenders must be removed (see

Section 8).



NOTE: The ignition switch must be in the ON

position.

VOLTAGE

(Wiring Harness Connector)

1. Set the meter selector to the D.C. Voltage position.

2. Connect the red tester lead to the orange wire; then

connect the black tester lead to ground.

AR622D

3. The meter must show battery voltage.



NOTE: If the meter shows no battery voltage,

troubleshoot the battery, fuse, switch, or the main
wiring harness.



NOTE: If the meter shows battery voltage, the

main wiring harness is good; proceed to test the
switch/component, the connector, and the switch
wiring harness for resistance.

RESISTANCE

(Switch Connector)



NOTE: The brake lever must be compressed for

this test. Also, the ignition switch must be in the
OFF position.

1. Set the meter selector to the OHMS position.

2. Connect the red tester lead to one black wire; then

connect the black tester lead to the other black

wire.

AR621D

3. When the lever is compressed, the meter must

show less than 1 ohm.



NOTE: If the meter shows more than 1 ohm of

r e s i s t a n c e , t r o u b l e s h o o t o r r e p l a c e t h e
switch/component, the connector, or the switch
wiring harness.

Coolant Temperature

and Cooling Fan

Switches

1. Connect the meter leads (selector in the OHMS

position) to the switch contacts.

2. Suspend the switch and a thermometer in a

container of water; then heat the water.



NOTE: Neither the switch nor the thermometer

should be allowed to touch the bottom of the con-
tainer or inaccurate readings will occur. Use wire
holders to suspend switch and thermometer.

733-554E

3. On the coolant temperature switch when the water

temperature reaches 112°-118° C (234°-244° F)

the meter should read a closed circuit.

! CAUTION

Always disconnect the battery when performing
resistance tests to avoid damaging the
multimeter.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды