Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 124

Страница: 124 / 210

5-23

100-Hour Belt

Inspection Mode

Clearing

Every 100 hours, the belt indicator light will illuminate

to alert for inspection. See Section 2 - Check-

ing/Replacing V-Belt. To reset the belt indicator light

use the following procedure.

1. Turn the ignition switch to the OFF position; then

disconnect the 4-pin connector.

2. Connect the Reset Connector (p/n 0486-161) into

the forward 4-pin connector; then turn the ignition

switch to the ON position. The belt indicator light

should flash rapidly.

3. Disconnect the belt indicator light switch

connector. The light should flash slowly. Allow

the light to flash for 10 seconds before turning the

ignition switch off.

4. Turn the ignition switch to the OFF position; then

remove the reset connector.

5. Connect the 4-pin connector and the belt indicator

light switch connector; then turn the ignition

switch to the ON position. The belt indicator light

should go off.

Engine Brake Actuator

Resistance

1. Remove the air duct boot; then disconnect the

actuator lead connector (A).

KX381

2. Use the multimeter and select the ohms function;

then measure resistance as follows: pins 4 (red) - 6

(black), 3-15 ohms; pins 1 (orange) - 3 (blue),

3500-6500 ohms; pins 2 (yellow) - 3 (blue),

630-5330 ohms. If readings are not as specified,

replace the engine brake actuator.

ATV2143A

Engine Brake Controller

Power Supply Voltage



NOTE: For the following tests, make sure the

battery is fully charged.



NOTE: Needle adapters will be required on the

multimeter leads as these tests are made with the
controller connected.

1. Select D.C. Voltage on the multimeter (B); then

turn the ignition switch ON.

2. In the brake controller (A), connect the red tester

lead to the orange wire terminal (9) and the black

tester lead to the black wire terminal (10). The

meter should read battery voltage.

! WARNING

V-belt inspection must be conducted in accordance
with Section 2. Belt separation and lock-up could
cause severe injury or death.

! CAUTION

Always disconnect the battery when performing
resistance tests to avoid damaging the
multimeter.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды