Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 161

Страница: 161 / 210

7-5

AF610D

11. Remove the circlip from the ball joint; then

remove the ball joint from the A-arm.

AF616D

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Clean all A-arm components in parts-cleaning

solvent.

2. Clean the ball joint mounting hole of all residual

Loctite, grease, oil, or dirt for installing purposes.

3. Inspect the A-arm for bends, cracks, and worn

bushings.

4. Inspect the ball joint mounting holes for cracks or

damage.

5. Inspect the frame mounts for signs of damage,

wear, or weldment damage.

INSTALLING

1. Apply green Loctite #609 to the entire outside

diameter of the ball joint; then install the ball joint

into the A-arm and secure with the circlip.

AF616D

2. Install the A-arm assemblies into the frame

mounts and secure with the cap screws. Only

finger-tighten at this time.

AF610D

3. Route the brake hose through the upper A-arm

shock absorber mount.

AF627D

4. Secure the lower eyelet of the shock absorber to

the upper A-arm. Tighten nut to 4.8 kg-m (35

ft-lb).

5. Secure the A-arm assemblies to the frame mounts

(from step 2). Tighten the cap screws to 4.8 kg-m

(35 ft-lb).

! CAUTION

Do not tighten the nut beyond the 4.8 kg-m (35
ft-lb) specification or the shock eyelet or mount
WILL be damaged.

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды