Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 25

Страница: 25 / 210

2-16

14.

Mode Button

— Used (in conjunction with the

Odometer/Trip Meters/Hour Meter) to shift the

odometer/trip meters/hour meter display through

the four modes: odometer, trip meter (A), trip

meter (B), and hour meter.

Frame/Welds/Racks

The frame, welds, and racks should be checked period-

ically for damage, bends, cracks, deterioration, broken

components, and missing components. If replacement

or repair constitutes removal, see Section 8.

Electrical Connections

The electrical connections should be checked periodi-

cally for proper function. In case of an electrical fail-

ure, check fuses, connections (for tightness, corrosion,

damage), and/or bulbs. If an electrical component

needs to be tested for proper function, see Section 5.

Hydraulic

Brake Systems

CHECKING/BLEEDING

The hydraulic brake systems have been filled and bled

at the factory. To check and/or bleed a hydraulic brake

system, use the following procedure.

1. With the master cylinder in a level position, check

the fluid level in the reservoir. If the level in the

reservoir is not visible in the sight glass, add DOT

4 brake fluid.

738-420A

CD091

2. Compress the brake lever/pedal several times to

check for a firm brake. If the brake is not firm, the

system must be bled.

738-437C

3. To bleed the brake system, use the following pro-

cedure.

A. Remove the cover and fill the reservoir with

DOT 4 Hi-Temp Brake Fluid (p/n 1639-799).

B. Install and secure the cover; then slowly

compress the brake lever several times.

C. Remove the protective cap, install one end of a

clear hose onto one FRONT bleeder screw, and

direct the other end into a container; then while

holding slight pressure on the brake lever, open

the bleeder screw and watch for air bubbles.

Close the bleeder screw before releasing the

brake lever. Repeat this procedure until no air

bubbles are present.

AF637D

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды