Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 145

Страница: 145 / 210

6-17

CC901



NOTE: Prior to installing the seal, apply grease

to the seal outside diameter.

4. Install the seal into the housing pressing evenly on

the outside edge until the seal is seated.

CD018

5. Repeat steps 1-4 for the opposite side.

INSTALLING DIFFERENTIAL

1. Align the splined input yoke with the front output

splines; then place the differential into position on

the frame and install the cap screws, washers, and

flex-lock nuts. Tighten to 6.2 kg-m (45 ft-lb).

Make sure the rubber boot is properly seated on

the input yoke.

KX161

AF905D

AF904D

2. Pour 275 ml (9.3 fl oz) of SAE 80W-90 hypoid

lubricant into the differential and install the filler

plug. Tighten to 2.2 kg-m (16 ft-lb).

3. Install the front drive actuator and tighten the

screws securely; then connect the lead to the main

harness.

KX164

4. Install the inner fender panels.



NOTE: To secure the side panels, use a

torx-head screw and three cable ties per side.

5. Install the front axles (see Drive Axles in this

section).

6. Secure the upper A-arms with cap screws and lock

nuts. Tighten to 4.8 kg-m (35 ft-lb).

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды