Arctic Cat 650 Twin2004 Скачать руководство пользователя страница 183

Страница: 183 / 210

8-17

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is
necessary.

1. Inspect wiring harness, three-prong connector,

lens, base, cap screws, and socket for damage.

2. Inspect all wires for corroding, pinching, and

cracking.

Seat

REMOVING/INSTALLING

3. Inspect the bulb for wattage, voltage, and proper

operation.

INSTALLING

1. Place the assembly into position on the frame and

secure with torx-head cap screws and any washers.

2. Tighten the cap screws securely.

3. Route the wiring harness over the rear frame; then

connect the three-prong connector.

0739-289

1. To remove the seat, pull the seat lock lever

backward (located under the rear rack between the

storage compartment and the frame). Raise the

rear of the seat and slide it rearward.

2. To lock the seat into positon, slide the front of the

seat into the seat retainers and push down firmly

on the rear of seat. The seat should automatically

lock into position.

KEY

1. Seat Assy
2. Cover
3. Foam
4. Base Assy
5. Base Bumper
6. Base Bumper
7. Staple
8. Plate
9. Rivet

10. Spring
11. Seat Latch

Содержание 650 Twin2004



















































































































































































































Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды

Arctic Cat 650 Twin2004, Руководство по обслуживанию

Результаты поиска

Содержание 650 Twin2004

Отзывы:

Похожие инструкции для 650 Twin2004

Бренды по названию

Популярные бренды