CTS55
Description of the Menus
1094.0006.55 9.35
E-7
9.9.5
Config MS Type and MS Type Edit
Config MS Type Menu
MS Type Edit Menu
In the main menus of the Manual test, Autotest, Quicktest and Module test a mobile type can be
selected.
The mobile types (100 max) are no longer network dependent and are available irrespective of network
setting. This means a mobile defined in one network (e.g. GSM900) can now be selected within another
network (e.g. GSM1900). Whereas pre – X2.06.3 Software will only display MS Types edited in its
created network.
The input and output attenuation’s are now split in to various sub-bands “low”, “mid” and “high”. The
low, mid and high input/output attenuation values will be used during the corresponding call established
ARFCN channels.
Band GSM850
Channel
Breakdown
GSM900
Channel
Breakdown
GSM1800
Channel
Breakdown
GSM1900
Channel
Breakdown
Low
128-169
975-1023 & 0-
30
512-635 512-611
Mid
170-210 31-78 636-759 612-711
High
211-251 79-124 760-885 712-810
The input/output attenuation values and ARFCN channel boundaries are applicable for Manual test,
Autotest and Quicktest. For Module test the ARFCN channel configuration differs and the “mid”
attenuation settings are always used irrespective of channel number.
The Sensitivity at level is for the Autotest BER and RXQual / RX Lev measurement only.
The Starting Time option initiates a small delay before initiating an ARFCN channel change.
The 2
nd
output attenuation value is for configuring the attenuation for the 2
nd
RF output.
The Handover mode option is a duplication of the option available within the Handover Details
Configuration (see section 9.9.13). The Handover mode option within this menu will take precedence
over Handover mode set in the Handover Details menu if the coupler is set to ON (see 9.7.3 Select MS
Type Menu).
With these two menus all mobile type parameters can be changed (
Edit
) new mobile types can be
inserted (
Insert
) or existing mobile types can be deleted (
Delete
). When inserting or editing the menu
on the right hand side appears.
The mobile type to be edited or deleted has to be selected with the arrow keys in the left menu.
The various attenuation’s for each network are edited by alternating the Network setting to the required
network. Each input att. / output att. field can then be edited by using the arrow keys.
The Remote Mobile MS Type is always first in the list and will never be sorted, it is used so that the
Remote Control Commands for setting the external attenuation will switch to configure the Mobile Type
only. Other Remote Control Commands will not effect this MS type. The Remote Mobile MS Type must
be selected before the CTS will actually use these values.
Summary of Contents for 1094.0006.50
