Optical Systems Design OSD2524, User Manual

Page: 95 / 402

OPTICAL SYSTEMS DESIGN
DOC ID: 10120001
OSD2524 OPERATOR MANUAL
PAGE 95
backend authentication server request from the switch. This scenario will loop forever. Therefore, the
server timeout should be smaller than the supplicant's EAPOL Start frame retransmission rate.
SINGLE 802.1X
In port-based 802.1X authentication, once a supplicant is successfully authenticated on a port, the whole
port is opened for network traffic. This allows other clients connected to the port (for instance through a
hub) to piggy-back on the successfully authenticated client and get network access even though they
really aren't authenticated. To overcome this security breach, use the Single 802.1X variant.
Single 802.1X is really not an IEEE standard, but features many of the same characteristics as does port-
based 802.1X. In Single 802.1X, at most one supplicant can get authenticated on the port at a time.
Normal EAPOL frames are used in the communication between the supplicant and the switch. If more
than one supplicant is connected to a port, the one that comes first when the port's link comes up will be
the first one considered. If that supplicant doesn't provide valid credentials within a certain amount of
time, another supplicant will get a chance. Once a supplicant is successfully authenticated, only that
supplicant will be allowed access. This is the most secure of all the supported modes. In this mode, the
Port Security module is used to secure a supplicant's MAC address once successfully authenticated.
MULTI 802.1X
Multi 802.1X is - like Single 802.1X - not an IEEE standard, but a variant that features many of the same
characteristics. In Multi 802.1X, one or more supplicants can get authenticated on the same port at the
same time. Each supplicant is authenticated individually and secured in the MAC table using the Port
Security module.
In Multi 802.1X it is not possible to use the multicast BPDU MAC address as destination MAC address
for EAPOL frames sent from the switch towards the supplicant, since that would cause all supplicants
attached to the port to reply to requests sent from the switch. Instead, the switch uses the supplicant's
MAC address, which is obtained from the first EAPOL Start or EAPOL Response Identity frame sent by
the supplicant. An exception to this is when no supplicants are attached. In this case, the switch sends
EAPOL Request Identity frames using the BPDU multicast MAC address as destination - to wake up any
supplicants that might be on the port.
The maximum number of supplicants that can be attached to a port can be limited using the Port Security
Limit Control functionality.
MAC-BASED AUTH.
Unlike port-based 802.1X, MAC-based authentication is not a standard, but merely a best-practices
method adopted by the industry. In MAC-based authentication, users are called clients, and the switch
acts as the supplicant on behalf of clients. The initial frame (any kind of frame) sent by a client is snooped
by the switch, which in turn uses the client's MAC address as both username and password in the
subsequent EAP exchange with the RADIUS server. The 6-byte MAC address is converted to a string on
the following form "xx-xx-xx-xx-xx-xx", that is, a dash (-) is used as separator between the lower-cased
hexadecimal digits. The switch only supports the MD5-Challenge authentication method, so the RADIUS
server must be configured accordingly.
When authentication is complete, the RADIUS server sends a success or failure indication, which in turn
causes the switch to open up or block traffic for that particular client, using the Port Security module.
Only then will frames from the client be forwarded on the switch. There are no EAPOL frames involved
in this authentication, and therefore, MAC-based Authentication has nothing to do with the 802.1X
standard.
The advantage of MAC-based authentication over 802.1X-based authentication is that the clients don't
need special supplicant software to authenticate. The disadvantage is that MAC addresses can be spoofed
by malicious users - equipment whose MAC address is a valid RADIUS user can be used by anyone.
Also, only the MD5-Challenge method is supported. The maximum number of clients that can be
attached to a port can be limited using the Port Security Limit Control functionality.